Foam Board Insulation in Pleasant Grove that stops thermal bridging
Rigid foam board insulation in Pleasant Grove, installed by local crews
Foam Board Insulation in Pleasant Grove is the fastest way to stop heat leaking through studs, rim joists, and foundation walls. We cut, fit, and seal rigid panels with taped seams so your furnace and AC stop fighting Utah County's 95-degree summers and 15-degree winters. If your basement feels cold or your upstairs bakes, we can fix it this week.
Foam Board Insulation in Pleasant Grove, Utah
Foam Board Insulation in Pleasant Grove is a rigid panel system - polyiso, EPS, or XPS - cut to fit stud bays, rim joists, basement walls, and attic rafters. Unlike fiberglass batts, rigid panels hold their R-value for decades, resist moisture, and cover the wood framing itself so heat cannot shortcut through the studs. We fasten each panel with cap nails or adhesive, then seal every seam with insulation tape so air leaks disappear before they start.
Pleasant Grove homes built before 1990 - especially around Old Pleasant Grove and the Historic District - usually run R-11 walls and bare rim joists. That is why upstairs bedrooms hit 82 degrees by 4pm in July while the basement stays cold enough to see your breath. Adding rigid foam board insulation Pleasant Grove brings those walls to R-15 or better and evens out the whole house. Most jobs land between $1,200 and $4,800 depending on square footage and whether we are finishing a basement or a full exterior wall.
Why Pleasant Grove homeowners add rigid foam board
Rigid panels do three things fiberglass cannot: they block thermal bridging, they shrug off moisture, and they hold their R-value for the life of the home. Here is what that means on your utility bill and in your comfort.
Lower energy bills
Rigid foam board insulation in Pleasant Grove typically cuts heating and cooling costs 15 to 25 percent. On a 2,000 sq ft home paying $180 a month, that is $27 to $45 back in your pocket every month - roughly $400 a year.
No more cold rooms
Thermal bridging through studs makes bedrooms over garages and basements miserable. Continuous foam board breaks that bridge, so the room above your garage stays within 3 degrees of the rest of the house instead of 10 to 15 degrees colder.
Moisture and mold control
Closed-cell foam board and XPS do not absorb water the way fiberglass batts do. In Pleasant Grove basements that see spring groundwater, that means no soggy insulation, no mold growth behind the drywall, and no musty smell drifting upstairs.
Pest resistance
Mice nest in fiberglass and cellulose. Rigid panels give them nothing to burrow into, and when we seal the rim joists with foam board and Great Stuff, we close the same gaps they were using to get in. Fewer entry points, fewer winter visitors.
How our foam board installation works
Every job follows the same five steps, whether we are insulating a single basement wall in Grove Creek or wrapping an entire home near Pleasant Grove Bench. You get a written scope, a fixed price, and a clean site when we leave.
Walkthrough and measure
We inspect the walls, rim joists, and attic with a thermal imaging camera and moisture meter. You see the hot and cold spots on screen. The walkthrough takes 30 to 45 minutes, and we leave you with a written scope the same day.
Panel selection
We match the board to the space: polyiso for interior walls, XPS for basement and crawl space, EPS where budget matters. Owens Corning, Johns Manville, and Dow panels all get the same careful fit. You approve the R-value before we order.
Cut and fit
We cut each panel with a foam board cutter and utility knife, friction-fit it between studs, and fasten with cap nails or construction adhesive. Gaps over a quarter inch get filled with Great Stuff. A typical basement takes one to two days.
Seal and tape
Every seam, corner, and penetration gets insulation tape or spray foam. This is the step that stops air leaks, and it is the step most crews skip. We photograph the finished wall so you can see the sealed assembly before drywall goes up.
Verify and clean
We re-scan with the thermal camera to confirm the cold spots are gone, then sweep and haul away every scrap. You get a final walkthrough and a 5-year workmanship warranty on the installation.
Four years of insulation work in Utah County
Skyseal Corner has been insulating Pleasant Grove homes since 2022. In four years we have completed hundreds of foam board, spray foam, and attic projects across Utah County, from 1940s bungalows near the Historic District to new builds in Pleasant Grove Heights. Our installers are trained on BPI Certified building-science principles, follow ENERGY STAR and IBC guidelines, and hold a current Utah contractor license. We carry respirators, thermal cameras, and moisture meters on every truck so the diagnosis happens before the invoice.
- Utah contractor license and full liability coverage on every crew
- BPI Certified building-science training for air sealing and moisture control
- Thermal imaging camera and moisture meter used on every walkthrough
- Experience with Owens Corning, Johns Manville, CertainTeed, and Dow foam products
- Hundreds of Pleasant Grove and Utah County installations completed since 2022
Why our Foam Board Insulation in Pleasant Grove wins on comfort
We are not the biggest insulation company in Utah County. We are the one that shows up, measures twice, and seals the seams nobody else bothers with. That is why most of our Pleasant Grove work comes from repeat customers and neighbor referrals.
Thermal scan before we quote
We do not guess at R-value. A thermal imaging camera shows us exactly where heat is escaping, so your quote covers the real problem instead of a generic wall package. You see the images before you sign anything.
Seams taped, not skipped
Air leaks at seams and rim joists can waste 20 percent of your heating budget. We tape and foam every joint, then re-scan to prove the cold spots are gone. That extra hour is why our walls actually perform.
Local crews, fast response
Our trucks are based in Pleasant Grove, so foam board insulation near me Pleasant Grove usually means same-week scheduling. Emergency calls for wet or fallen insulation get a 24/7 response, including weekends.
Fixed pricing, no surprise add-ons
You get one number before work starts. If we open a wall and find mold or pest damage, we stop, show you, and quote the repair before touching it. No mystery line items on the final invoice.
What our Foam Board Insulation service includes
Every foam board job covers the full assembly, not just the panels. We handle the thermal scan, the cutting and fitting, the air sealing, and the final verification. Add-ons like drywall repair or insulation removal are quoted separately after we open the wall.
What's Included
Thermal scan and moisture check
We scan every wall and rim joist with a thermal imaging camera and check for moisture with a meter. You see the images and get a written scope the same day.
Rigid panel cutting and fitting
We cut polyiso, XPS, or EPS to fit each stud bay and rim joist, then fasten with cap nails or adhesive. Panels are friction-fit tight, with gaps under a quarter inch.
Air sealing and taping
Every seam, corner, and penetration gets insulation tape or Great Stuff spray foam. This is the step that stops air leaks and makes the R-value actually perform.
Vapor barrier coordination
We install or tie into the vapor barrier so the wall assembly dries in the right direction. In Pleasant Grove basements, that prevents moisture buildup behind the foam.
Final thermal verification
We re-scan the finished wall and show you the before-and-after images. If a cold spot remains, we fix it before we pack up. You get a 5-year workmanship warranty.
Problems our foam board insulation solves in Pleasant Grove
Most Pleasant Grove insulation calls come down to four issues: cold rooms, high bills, moisture, and pests. Rigid foam board addresses all four because it covers the framing, not just the cavity.
Upstairs bedrooms over garages stay 10 degrees colder
You avoid those rooms in winter and run space heaters that spike the power bill. The root cause is thermal bridging through the studs, which fiberglass batts cannot stop.
We install continuous foam board across the studs and seal the rim joists with spray foam. The room above your garage comes within 3 degrees of the rest of the house.
Basement walls sweat and smell musty in spring
Moisture builds behind fiberglass batts, mold grows, and the smell drifts upstairs. Left alone, the framing itself starts to rot.
We remove the wet batts, dry the wall, and install XPS foam board with taped seams. Closed-cell foam does not absorb water, so the wall stays dry through snowmelt season.
Mice nest in the insulation every fall
Fiberglass and cellulose give rodents an easy burrow. Once they are in the wall, they chew wiring and leave droppings that trigger allergies.
Rigid foam board gives them nothing to nest in. We seal the rim joists and any gaps with foam board and Great Stuff, closing the entry points they were using.
Energy bills climb every year despite new windows
New windows help, but if the walls are R-11 and the rim joists are bare, you are still heating the neighborhood. The bill keeps climbing while comfort stays flat.
We scan the envelope, find the real leaks, and add foam board where it pays back fastest. Most Pleasant Grove homes see 15 to 25 percent lower heating and cooling costs.
When Pleasant Grove homeowners call us for foam board
Finishing a basement in Pleasant Grove Heights and the concrete walls are bare.
We frame the walls, install XPS foam board against the concrete, tape the seams, and coordinate with your drywall crew. The assembly stays dry and hits R-15 without stealing much floor space.
A finished basement that stays within 3 degrees of the main floor and passes Utah County inspection without a moisture issue.
An older home near the Historic District has original 2x4 walls with no sheathing.
We remove the old batts, add 1-inch polyiso foam board to the interior face, and seal the rim joists in the basement. The wall goes from R-11 to R-17 without tearing off the siding.
Upstairs bedrooms stop baking in July and the furnace runs less in January. Most homeowners see the bill drop within two months.
A pole barn or shop near Pleasant Grove Industrial Park needs year-round use.
We cut and fasten foam board between the girts and on the ceiling, then seal every seam with tape. Metal ribs conduct heat, so continuous board is the only way to stop the sweating.
A shop that stays above freezing in winter and below 80 degrees in summer, with no condensation dripping on tools.
A crawl space under a Grove Creek home stays damp and the floors are cold.
We line the crawl space walls with XPS foam board, seal the vents, and insulate the floor joists. The moisture meter reading drops and the floors warm up.
Warmer floors, no musty smell, and no mold growth on the joists. The crawl space stays dry through spring snowmelt.
Tools and methods we use
Tools & Equipment
Thermal imaging camera
Finds the hot and cold spots in your walls before we quote, and verifies the fix after installation. You see the images on screen.
Moisture meter
Checks wall cavities and rim joists for hidden moisture. Wet framing has to dry before foam board goes on, or mold grows behind it.
Foam board cutter and utility knife
Cuts polyiso, XPS, and EPS to a friction fit inside stud bays. Clean cuts mean tighter seams and fewer air leaks.
Spray foam gun and Great Stuff
Seals the odd gaps around electrical boxes, plumbing, and rim joist corners that rigid panels cannot cover.
Respirator and stapler
Keeps our crew safe from dust and fumes, and fastens house wrap and vapor barrier over the finished assembly.
Methods
Continuous insulation over framing
We run foam board across the studs, not just between them, so heat cannot shortcut through the wood. This is the single biggest upgrade for a Pleasant Grove wall that currently has only fiberglass batts.
Rim joist sealing
The rim joist is the biggest air leak in most homes. We cut foam board to fit each bay, seal the edges with spray foam, and tape the seams. This one step often cuts drafts more than any other.
Taped seam air barrier
Every panel joint gets insulation tape or spray foam. Untaped seams leak air and drop the effective R-value by 20 percent or more, so we treat the tape as part of the insulation, not a finishing touch.
Vapor barrier coordination
We install or tie into the vapor barrier so the wall dries toward the right side. In Pleasant Grove basements, that means keeping moisture out of the cavity while letting the concrete breathe.
How foam board insulation performs in Pleasant Grove
Pleasant Grove sits in Utah County at about 4,600 feet, which means 95-degree July afternoons and single-digit January nights. That swing punishes fiberglass, which loses R-value when it gets damp or compressed. Rigid foam board holds steady through both extremes. The housing stock matters too: homes near Old Pleasant Grove and the Historic District were built before modern energy codes, often with 2x4 walls and no sheathing, while new builds in Pleasant Grove Heights just need the rim joists sealed. We size the R-value to the wall, not to a generic chart. If you are comparing foam board insulation cost Pleasant Grove UT, remember that the cheapest panel is not the cheapest job - a properly taped R-15 wall beats an untaped R-20 every time. We also handle foam board insulation Pleasant Grove basement projects, where XPS against the concrete is the standard fix for cold floors and spring moisture.
Service Areas
Pre-1960 homes with 2x4 walls and no sheathing. These need continuous foam board on the interior face to reach a usable R-value.
Newer construction with decent wall insulation but bare rim joists. Sealing the rim joist with foam board is the fastest comfort upgrade here.
Crawl spaces and basements near the creek see more groundwater. XPS foam board and sealed vents are the standard fix.
Exposed lots with wind-driven air leaks. Rim joist sealing and taped seams make the biggest difference on these homes.
Local Considerations
Winter lows drop into the single digits
Thermal bridging through studs becomes obvious when the outside air is 5 degrees. Continuous foam board is the only fix that stops the studs from conducting cold into the room.
Spring snowmelt raises basement moisture
Fiberglass batts soak up groundwater and lose R-value. Closed-cell foam board and XPS stay dry, so the wall keeps performing through April and May.
Summer afternoons hit 95 degrees
Attic and wall cavities bake, and heat radiates into upstairs rooms. Foam board with a radiant barrier or foil facing reduces that heat gain before it reaches the living space.
Older homes have no modern vapor barrier
We install or tie into a vapor barrier so the wall dries in the right direction. Without it, foam board can trap moisture and cause mold growth.
1950s bungalow near Old Pleasant Grove
Original 2x4 walls with compressed R-7 batts and bare rim joists. Upstairs bedrooms hit 84 degrees in July and the furnace ran constantly in January. Power bills averaged $210 a month.
We added 1-inch polyiso foam board to the interior walls and sealed every rim joist with foam board and Great Stuff. Upstairs now stays within 2 degrees of the main floor. The next July bill came in at $148.
Maintenance & Follow-up
Keep the taped seams intact and re-check the rim joist seal every few years. If you remodel, do not cut into the foam board without sealing the new gap.
Bare concrete walls with visible condensation in spring. The homeowner wanted a finished rec room but the contractor warned that fiberglass would mold within a year.
We installed 2-inch XPS foam board against the concrete, taped the seams, and sealed the rim joists. The wall now reads R-15 and the moisture meter stays dry through snowmelt. The rec room holds 68 degrees all winter.
Maintenance & Follow-up
Run a dehumidifier in the first month after finishing, then check the base of the wall each spring for any sign of moisture.
Metal walls with no insulation. The shop sweated in winter, tools rusted, and the owner could not work in January without a heavy coat. Summer afternoons pushed the interior past 95 degrees.
We cut and fastened foam board between the girts and on the ceiling, then taped every seam. The shop now stays above 40 degrees in winter and below 80 in summer. Condensation stopped dripping on the tools.
Maintenance & Follow-up
Inspect the taped seams each fall and replace any tape that has peeled. Keep the vents clear so the space can still breathe.
How much does foam board insulation cost in Pleasant Grove UT?
Most Pleasant Grove foam board jobs run $1,200 to $4,800 in 2026, with a typical basement landing near $2,400. Cost depends on square footage, R-value, and whether we are covering rim joists or full walls. Polyiso costs more than EPS but delivers a higher R-value per inch. We give you a fixed written price after the thermal scan, so the number does not move.
What is the best foam board insulation in Pleasant Grove Utah?
Polyiso is the best all-around choice for interior walls because it delivers R-6 per inch and handles Utah County's temperature swings. XPS wins in basements and crawl spaces where groundwater is a factor, since it resists moisture better. For tight budgets, EPS at R-4 per inch still beats fiberglass batts. We stock Owens Corning, Johns Manville, and Dow panels and match the board to your wall.
Who installs foam board insulation near me in Pleasant Grove?
Skyseal Corner installs foam board insulation across Pleasant Grove and Utah County from our local base. We handle cutting, fitting, fastening, taping, and verification with a thermal camera. Call (855) 927-7517 and we will schedule a walkthrough, usually within the same week. Our crews carry a Utah contractor license and full liability coverage.
Does foam board insulation work in Pleasant Grove?
Yes. Foam board insulation works well in Pleasant Grove because it blocks thermal bridging, which is the biggest weakness in this area's older wood-framed homes. Rigid panels also resist the moisture that comes with spring snowmelt and irrigation. We have installed it in basements, rim joists, and attic rafters across Utah County with measurable bill reductions of 15 to 25 percent.
Licensed, certified, and reviewed
Certifications
Reviews
Skyseal scanned our walls, found the rim joist leaks, and installed foam board in one day. The upstairs is finally comfortable and our July bill dropped $61. They cleaned up and explained everything.
We had mice in the walls every fall. Skyseal sealed the rim joists with foam board and Great Stuff and we have not seen a single dropping since. Two winters, zero pests.
Finished our Pleasant Grove basement with XPS foam board and taped every seam. The moisture meter stays dry through spring and the room holds 68 degrees all winter. Fair price, no surprises.
Called for a quote on foam board insulation and they showed up with a thermal camera the same week. The images made the problem obvious. Fixed price, professional crew, and a 5-year warranty.
Related Services
Spray Foam Insulation
Spray foam fills the odd gaps that rigid panels cannot reach, like electrical boxes and rim joist corners. We often pair it with foam board in Pleasant Grove basements for a fully sealed assembly.
Spray Foam InsulationAttic Insulation
Foam board on the attic rafters plus blown-in insulation on the floor creates a double barrier. Pleasant Grove homes with hot upstairs bedrooms usually need both to hit comfortable summer temps.
Attic InsulationGarage Door Insulation
An insulated garage door works best when the walls around it are also sealed. We add foam board to garage walls in Pleasant Grove so the door kit actually holds heat instead of fighting an open cavity.
Garage Door InsulationFiberglass Insulation
Fiberglass batts still make sense in open interior walls where budget matters. We combine them with rigid foam board in Pleasant Grove to cover both the cavity and the studs for full R-value.
Fiberglass InsulationInsulation Installers Near Me
Our Pleasant Grove-based installers handle foam board, spray foam, and blown-in work under one crew. One call covers the whole envelope instead of juggling three subcontractors.
Insulation Installers Near Me24/7 Insulation Installation
Storm damage, burst pipes, or a failed remodel can leave walls exposed overnight. We offer 24/7 insulation installation in Pleasant Grove to close the envelope before the next freeze.
24/7 Insulation InstallationEmergency Insulation Repair
Wet or fallen insulation needs fast removal to prevent mold growth. Our emergency crews respond across Pleasant Grove, dry the cavity, and reinstall foam board once the wall is sound.
Emergency Insulation RepairBasement Insulation
Basements are where foam board shines. We insulate Pleasant Grove basement walls with XPS or polyiso, seal the rim joists, and turn a cold storage room into usable living space.
Basement InsulationHome Insulation
A full-home insulation plan starts with foam board on the problem walls and works outward. We assess the whole Pleasant Grove house, then prioritize the upgrades with the fastest payback.
Home InsulationRockwool Insulation
Rockwool mineral wool adds fire resistance and sound control where foam board is not ideal. We use it alongside rigid panels in Pleasant Grove homes near busy streets or shared walls.
Rockwool InsulationCellulose Insulation
Cellulose fills attic and wall cavities at a lower cost than foam. We combine it with foam board in Pleasant Grove to cover the flat surfaces and the framing in one scope.
Cellulose InsulationWindow Insulation
Windows leak air even when the walls are sealed. We add foam board to the surrounding framing and seal the rough openings so Pleasant Grove window drafts stop at the source.
Window InsulationCeiling Insulation
Ceilings under cold attics lose heat fast. Foam board on the ceiling plane plus blown-in above keeps Pleasant Grove rooms warmer without tearing out the drywall.
Ceiling InsulationMetal Building Insulation
Metal buildings sweat and conduct heat through every rib. Rigid foam board with taped seams is the standard fix for Pleasant Grove shops and pole barns.
Metal Building InsulationRoof Insulation
Roof decks over cathedral ceilings need rigid board to prevent ice dams. We install foam board in Pleasant Grove attics where venting is tight and batt insulation cannot fit.
Roof InsulationSoundproof Insulation
Foam board plus mineral wool deadens sound between rooms and floors. Pleasant Grove homeowners near Grove Creek use it to quiet bedrooms facing the road.
Soundproof InsulationDouble Bubble Insulation
Double bubble foil works as a radiant barrier in attics and garages. We pair it with foam board in Pleasant Grove where reflective control and R-value are both needed.
Double Bubble InsulationPole Barn Insulation
Pole barns need rigid panels that will not sag between girts. We cut and fasten foam board to Pleasant Grove barn walls and ceilings for year-round use.
Pole Barn InsulationFoil Insulation
Foil insulation reflects radiant heat in attics and metal buildings. Combined with foam board in Pleasant Grove, it reduces summer heat gain before it reaches your living space.
Foil InsulationInsulation Near Me
Searching insulation near me in Pleasant Grove brings up plenty of options. We are the local crew that shows up with a thermal camera and a fixed price, not a call center.
Insulation Near MeBlown In Insulation
Blown-in insulation fills irregular attic cavities fast. We use it above foam board in Pleasant Grove to top off R-value without adding weight to the ceiling.
Blown In InsulationSpray Foam Insulation Near Me
Spray foam near me in Pleasant Grove usually means a two-week wait. Our crews carry both spray foam and rigid board so we can seal and insulate in one visit.
Spray Foam Insulation Near MeCrawl Space Insulation
Crawl spaces in Pleasant Grove stay damp and cold. We line the walls with XPS foam board and seal the vents to keep moisture out and floors warm.
Crawl Space InsulationWall Insulation
Exterior and interior walls both benefit from rigid panels. We install foam board in Pleasant Grove walls where fiberglass has sagged or never filled the cavity properly.
Wall InsulationInsulation Removal
Wet, moldy, or pest-infested insulation has to come out before new foam board goes in. We remove and dispose of old material across Pleasant Grove, then rebuild the assembly.
Insulation RemovalFloor Insulation
Floors over crawl spaces and garages lose heat through the framing. Rigid foam board under the subfloor keeps Pleasant Grove rooms warmer and cuts drafts at floor level.
Floor InsulationGet your Foam Board Insulation in Pleasant Grove quote
One call gets a thermal scan, a fixed price, and a crew that seals every seam. We are licensed, local, and backed by a 5-year workmanship warranty. Call (855) 927-7517 and we will schedule your Pleasant Grove walkthrough this week.